I have an issue with mounting a cheap smart watch in #linux: Device is seen by the kernel, but never registered as a storage device /dev/sd*:
-
Ok, the plot thickens. When booting from the Linux Mint USB stick, the USB ports work. But when booting the installed version, USB ports are broken. Why??
So my current working hypothesis is: Live Linux Mint uses kernel 6.14, my installation uses kernel 6.17. This is probably what causes the regression?
So I might want to downgrade the kernel...
#linux #linuxmint -
So my current working hypothesis is: Live Linux Mint uses kernel 6.14, my installation uses kernel 6.17. This is probably what causes the regression?
So I might want to downgrade the kernel...
#linux #linuxmintNope, that was not it. I downgraded to Linux 6.14.0-37, but USB still doesn't work. So it must be something with my installation! But what?
-
Nope, that was not it. I downgraded to Linux 6.14.0-37, but USB still doesn't work. So it must be something with my installation! But what?
@root42 I still have some problemas mounting usb from friends in Ubuntu Focal. Can you believe that?
May it be a permissions issue? -
Nope, that was not it. I downgraded to Linux 6.14.0-37, but USB still doesn't work. So it must be something with my installation! But what?
I am onto something: Attaching an OLD Apple keyboard with a USB-C to A adapter WORKS. But all my USB3.x devices do NOT work!
So how do I tell the USB controller to also work with USB3 devices...? Which works on the live thumbdrive!
-
Nope, that was not it. I downgraded to Linux 6.14.0-37, but USB still doesn't work. So it must be something with my installation! But what?
@root42 it sounds like it does not load some usb drivers. But for default usb never seen that happen.
-
I am onto something: Attaching an OLD Apple keyboard with a USB-C to A adapter WORKS. But all my USB3.x devices do NOT work!
So how do I tell the USB controller to also work with USB3 devices...? Which works on the live thumbdrive!Yes, so it seems the controller is stuck in EHCI mode, instead of switching to xHCI for USB3 devices. Bummer... how to switch it back...?
-
@dr_laemmerbein Yes, it works fine in macOS as mass storage. No issue. However I just noticed that no other USB mass storage gets detected either. This is on the 2017 13" MacBook Pro. I have tried a USB thumb drive (That I installed Mint off of!) and a card reader with an SD card. No dice. Something is seriously wrong.
@root42 Did you install a kernel update by any chance? Then you might need a reboot to make it work again, I ran into that a few times...
-
I have an issue with mounting a cheap smart watch in #linux: Device is seen by the kernel, but never registered as a storage device /dev/sd*:
usb 1-2: new full-speed USB device number 3 using xhci_hcd
usb 1-2: New USB device found, idVendor=0e8d, idProduct=0002, bcdDevice= 1.00
...
usb-storage 1-2:1.0: USB Mass Storage device detected
scsi host0: usb-storage 1-2:1.0@root42 I also had this problem once where the kernel showed the usb drive was plugged in but no /dev/sd* showed up, the problem was the usb kernel modules weren't loaded so 'modeprobe usb' or a similar modeprobe command to that fixed it
-
Yes, so it seems the controller is stuck in EHCI mode, instead of switching to xHCI for USB3 devices. Bummer... how to switch it back...?
@root42 Is your USB controller properly listed in `lspci`? And if it is, what kernel options does it use (see with `lspci -s <address of controller> -k`. For example, here's mine:
04:00.3 USB controller: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne USB 3.1
Subsystem: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne USB 3.1
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci -
@root42 Did you install a kernel update by any chance? Then you might need a reboot to make it work again, I ran into that a few times...
@dr_laemmerbein lots of reboots...
-
@root42 Is your USB controller properly listed in `lspci`? And if it is, what kernel options does it use (see with `lspci -s <address of controller> -k`. For example, here's mine:
04:00.3 USB controller: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne USB 3.1
Subsystem: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne USB 3.1
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci@sebastiaanfranken Seems so:
07:00.0 USB controller: Intel Corporation JHL6540 Thunderbolt 3 USB Controller (C step) [Alpine Ridge 4C
2016] (rev 02)
Subsystem: Intel Corporation JHL6540 Thunderbolt 3 USB Controller (C step) [Alpine Ridge 4C 2016]
Kernel driver in use: xhci_hcd -
@sebastiaanfranken Seems so:
07:00.0 USB controller: Intel Corporation JHL6540 Thunderbolt 3 USB Controller (C step) [Alpine Ridge 4C
2016] (rev 02)
Subsystem: Intel Corporation JHL6540 Thunderbolt 3 USB Controller (C step) [Alpine Ridge 4C 2016]
Kernel driver in use: xhci_hcd@root42 Ok, so that's good. Also the fact the proper hcd (xhci_hcd) module is loaded is good. Anything related to it in your system journal? And if you want you can get more output / info with
> sudo lspci -s 07:00.0 -k -v
-
@root42 Ok, so that's good. Also the fact the proper hcd (xhci_hcd) module is loaded is good. Anything related to it in your system journal? And if you want you can get more output / info with
> sudo lspci -s 07:00.0 -k -v
@sebastiaanfranken First the lspci output
-
@sebastiaanfranken First the lspci output
-
@dr_laemmerbein lots of reboots...
@root42 Maybe you can get some hints by running `dmesg -w` in a terminal as root. This will show you all the kernel events and if you plug in your USB drive you should see some logs related to that. Maybe you'll get an error message or something like that.
-
Yes, so it seems the controller is stuck in EHCI mode, instead of switching to xHCI for USB3 devices. Bummer... how to switch it back...?
@root42 Check the pins in the connectors. I had a problem like this where in a thumb drive some pins belonging to USB3 were bent / damaged and it would not work in a USB3 port. Although it worked fine in a USB2 port, those 4 pins were not damaged. -
@root42 Check the pins in the connectors. I had a problem like this where in a thumb drive some pins belonging to USB3 were bent / damaged and it would not work in a USB3 port. Although it worked fine in a USB2 port, those 4 pins were not damaged.@root42 with USB-C it could also be the wrong type of cable.
-
@root42 with USB-C it could also be the wrong type of cable.
@robert no. It works in the Live thumbdrive. Only the proper install on the ssd is botched. The ports work fine.
-
@root42 Maybe you can get some hints by running `dmesg -w` in a terminal as root. This will show you all the kernel events and if you plug in your USB drive you should see some logs related to that. Maybe you'll get an error message or something like that.
@dr_laemmerbein I am doing that. No logs when plugging in USB 3 devices. Zip. Zilch. Nada. That’s the weird thing.
-
@root42 with USB-C it could also be the wrong type of cable.
@robert the USB C thumbdrive connects without a cable. It works in the live system, not in the installed system.
