Q1: Say hi, and tell us what you’ve been doing this week.
-
@wokstation @suearcher @MakersHour that isn't fun
-
@MakersHour thanks! the big day is tomorrow, and the to do list is finally getting shorter
-
@suearcher @MakersHour I keep looking at our rhubarb and contemplating doing something with it - upside down cake sounds delicious!
It's dead simple -I just put chopped up stalks in the bottom of the cake tin, sprinkled with sugar (and ground ginger if you like) and then pour a plain sponge batter over it and bake.
I call it upside down cake, but you can serve and eat it whichever way up you like!
-
A1 goedeavond! not much this week. Did some work replumbing the makerspace waste water system at the weekend. As well as some 3d printing. Diary is too full right now.
@quixoticgeek
How's your ankle now? -
It's dead simple -I just put chopped up stalks in the bottom of the cake tin, sprinkled with sugar (and ground ginger if you like) and then pour a plain sponge batter over it and bake.
I call it upside down cake, but you can serve and eat it whichever way up you like!
@suearcher @MakersHour nice, thank you
-
@quixoticgeek
How's your ankle now?@MakersHour A lot better. I can walk without a crutch now. Which is a big improvement.
-
@Indigoatcrafts
Awww, that is such a lovely thing to do for the staff team.I hope the recovery continues smoothly, and you are not out of action for too long.
@MakersHour I had to pop in for paperwork today and I haven't got close to finishing stuff so they just got a stack of thank you biscuits
-
Q1: Say hi, and tell us what you’ve been doing this week. #MakersHour
@MakersHour A1 (Hello): Hi, I'm kbob. I'm finally getting back into the groove this week. I fixed my printer. I've printed a few things, and I've resumed work on the bubble universe with color themes.
-
@wokstation @MakersHour the discharge day was scary but yes getting out has been good. I'm doing better than I thought. Only 1 bad fall
-
@MakersHour A lot better. I can walk without a crutch now. Which is a big improvement.
@quixoticgeek
Excellent.
That is gaining a leg and an arm back into use.
I hope it continues to improve. -
@MakersHour A1 (Hello): Hi, I'm kbob. I'm finally getting back into the groove this week. I fixed my printer. I've printed a few things, and I've resumed work on the bubble universe with color themes.
@kbob
I have completely failed to fix my printer, but it is a HP Pro 8200, that stopped working when I put in fresh ink! Nothing will work now. -
@kbob
I have completely failed to fix my printer, but it is a HP Pro 8200, that stopped working when I put in fresh ink! Nothing will work now.@MakersHour Sorry to hear that. My printer is 3D. Flatland printers are whole new vistas of failure modes.
-
@MakersHour Sorry to hear that. My printer is 3D. Flatland printers are whole new vistas of failure modes.
@kbob
Yes, it is a bloody pain.
It was working fine up until it needed ink. It recognised the ink as genuine and then reported a problem and wanted me to phone HP.
Repair Cafe couldn't fix it, and YouTube hints videos didn't make any difference either.I will need to get another printer, I think.
-
Q1: Say hi, and tell us what you’ve been doing this week. #MakersHour
Aethon. Outside of making I look after the house, carer and a fair bit of rural work. Making wise, not a lot as I damaged my shoulder putting up some fencing. I made some leather sheaths for the local shearers.
