If you have strong opinions about #Mesh networking, please let me know.
-
@edronik @thechaoszone I'll give it a go. Ta!
-
@Edent For Meshcore in the UK you need to change your radio settings:
Frequency: 869.618
Bandwidth: 62.5
Spreading Factor: 8
Coding Rate: 8
Transmit Power: 22 -
OK my #Meshcore friends, what am I doing wrong?
Board is on the 3rd floor (over 6m above ground height.
Powered on, connected via Bluetooth, by a window.
Set to UK long range.
Been up for about 30 minutes and hasn't discovered any neighbours.
I know there are a couple of repeaters near-ish.
Just a case of wait and hope? Stick it in the loft? Increase power?
Any help and speculation welcomed




@Edent UK/EU Narrow. The default is wrong

-
-
@Edent UK/EU Narrow. The default is wrong

@M0YNG cheers. Have switched over. Nothing discovered yet.
-
@Edent This is the EU/UK (Narrow) preset.
-
@M0YNG cheers. Have switched over. Nothing discovered yet.
@Edent not shocking. the repeaters are usually set to advertise with large gaps (I think 12 hours)
Put a ping out on the test channel (hashtag test) and check if "sent" changes to "heard 1 repeat". If so, one repeater heard you and you heard it repeat your message.
Try a couple of times if it didn't work immediately...If not, try another position!
-
-
@Edent not shocking. the repeaters are usually set to advertise with large gaps (I think 12 hours)
Put a ping out on the test channel (hashtag test) and check if "sent" changes to "heard 1 repeat". If so, one repeater heard you and you heard it repeat your message.
Try a couple of times if it didn't work immediately...If not, try another position!
@M0YNG thanks. Nothing yet. Trying a different window

-
OK my #Meshcore friends, what am I doing wrong?
Board is on the 3rd floor (over 6m above ground height.
Powered on, connected via Bluetooth, by a window.
Set to UK long range.
Been up for about 30 minutes and hasn't discovered any neighbours.
I know there are a couple of repeaters near-ish.
Just a case of wait and hope? Stick it in the loft? Increase power?
Any help and speculation welcomed




- problem is the window
- this type of antenna dont like to kink
- antennas love metal-bases to reduce noise from electronics
-
- problem is the window
- this type of antenna dont like to kink
- antennas love metal-bases to reduce noise from electronics
@grutzifix ok. Where do you suggest I put it? Not sure how waterproof it is

-
OK my #Meshcore friends, what am I doing wrong?
Board is on the 3rd floor (over 6m above ground height.
Powered on, connected via Bluetooth, by a window.
Set to UK long range.
Been up for about 30 minutes and hasn't discovered any neighbours.
I know there are a couple of repeaters near-ish.
Just a case of wait and hope? Stick it in the loft? Increase power?
Any help and speculation welcomed




Aha! I had to unbend the antenna

Now receiving #Meshcore messages. Don't know if any of mine are being seen though.

-
Aha! I had to unbend the antenna

Now receiving #Meshcore messages. Don't know if any of mine are being seen though.

@Edent I haven't seen your messages (get to Bristol).
When you send a message do you see any repeats? Under your blue message bubble it may say something like βHeard 1 repeatβ. If it just says "Sent" then it is possible no one heard you.
You may be able to hear things without anyone hearing you.
-
OK my #Meshcore friends, what am I doing wrong?
Board is on the 3rd floor (over 6m above ground height.
Powered on, connected via Bluetooth, by a window.
Set to UK long range.
Been up for about 30 minutes and hasn't discovered any neighbours.
I know there are a couple of repeaters near-ish.
Just a case of wait and hope? Stick it in the loft? Increase power?
Any help and speculation welcomed




@Edent uk narrow
-
@Edent I haven't seen your messages (get to Bristol).
When you send a message do you see any repeats? Under your blue message bubble it may say something like βHeard 1 repeatβ. If it just says "Sent" then it is possible no one heard you.
You may be able to hear things without anyone hearing you.
@dan not seeing any repeats so, yeah, I expect I'm on read only at the moment

-
Aha! I had to unbend the antenna

Now receiving #Meshcore messages. Don't know if any of mine are being seen though.

@Edent oh, antennas and antenna placement can be very weird to understand and to debug. in general it's better to not have your whip antenna near to a big piece of metal because it will couple with it and throw everything off.
recommendation: take a photograph, measure for a day, move something around, take another photograph, do another day's measurements, repeat.
If you can get the antenna outside rather than inside it will make a difference, but that's not always easy
-
OK my #Meshcore friends, what am I doing wrong?
Board is on the 3rd floor (over 6m above ground height.
Powered on, connected via Bluetooth, by a window.
Set to UK long range.
Been up for about 30 minutes and hasn't discovered any neighbours.
I know there are a couple of repeaters near-ish.
Just a case of wait and hope? Stick it in the loft? Increase power?
Any help and speculation welcomed




@Edent this doesn't help but I assumed Northampton wouldn't have any #meshtastic traffic and now I'm interested

-
@dan not seeing any repeats so, yeah, I expect I'm on read only at the moment

-
-