And our last question this week:
-
And our last question this week:
Q8. What did you see this week? Share a photo if you'd like. Cycling related or not is fine. Tell us about it!
#BikeNiteQ #BikeNite #BikeTooter #Cycling #MastoBikes cc @bikenite
@ascentale @bikenite A8 the valleys and hills of Calderfornia seen from the Rochdale canal and cobbles betwixt Littleborough and Manchester…
Too much pressure in my tyres so I am feeling it today (left my rear tyre over-pumped overnight to seat the bead and forgot to let some air out before I set off).
-
@ascentale @bikenite A8. I “finished” rebuilding my old bike, so a bike photo this week. I’m mostly happy with the results, I need a procure a new stem to bring the handlebars up and back a little. The shifting is not quite right, so I need to figure that out. And short pull bar shifters with long pull brakes, so kinda mushy braking, so I still need to figure that out. I knew this would be an issue, but the Microshift Sword brakes claim to have a 1.5 pull ratio, so I was hoping it would be better. Oh and the steering is a little twitchy, which I think will be better with the handle bars higher and closer. #BikeNite
@rand @ascentale @bikenite That's really nice! #BikeNite
-
@rand was that the stem from the stock riser / flat handlebar? You might get more pull with the levers slightly farther up the curve, if the extra reach from the drops is tolerable. There is also the Problem Solvers pulley thing that goes on the caliper and doubles the cable pull problemsolversbike.com/products/travel-agent
@enobacon The stem is from my other bike, which was the wrong size (was too long and on that bike it was angled down), but I figured it was a good starting point.
I think I can tighten up the brakes a little bit, but the return springs are not working well, I don't really understand why, the brakes are only about 5 years old. One arm in particular just has almost no tension. I'll also look into moving the bars up some. I have big enough hands, so reach is not a problem. Unfortunately problem solvers doesn't sell their pulley thing anymore, so I need to find some pre-owned ones (I did run across a single one once). #BikeNite
-
@rand @ascentale @bikenite Wouldn't moving the bars in that direction make the steering more twitchy?
@LovesTha @ascentale @bikenite Idk, but my often wrong intuition thinks that if your hands are closer to the perpendicular of the steering tube that it would be less. But I suppose I'll find out (the old flat bars were a but closer). #BikeNite
-
@enobacon The stem is from my other bike, which was the wrong size (was too long and on that bike it was angled down), but I figured it was a good starting point.
I think I can tighten up the brakes a little bit, but the return springs are not working well, I don't really understand why, the brakes are only about 5 years old. One arm in particular just has almost no tension. I'll also look into moving the bars up some. I have big enough hands, so reach is not a problem. Unfortunately problem solvers doesn't sell their pulley thing anymore, so I need to find some pre-owned ones (I did run across a single one once). #BikeNite
@rand assuming the pivots aren't binding, are the brake springs adjustable? Most have an arc 3 holes that the spring end can be clocked to before mounting, plus the small screw for finer tuning.
-
@rand assuming the pivots aren't binding, are the brake springs adjustable? Most have an arc 3 holes that the spring end can be clocked to before mounting, plus the small screw for finer tuning.
@enobacon They are adjustable, with a screw to adjust spring tension and the three holes on the post. Originally I had them all on the middle hole, but the return was not a much as I wanted so I moved them to the top hole (greatest tension), but then one of the arms apparently "failed" it still works, but a lot less tension, for that brake, I have the failed arm in the high tension hole and the working arm in the medium hole. Balances better (the screw on the failed arm does not change the tension). I don't see a way to disassemble the arm to see what is going on inside (other than destroying it).
They are Promax P-1 108mm arms. the 85mm arms I think would be just a few mm to short and the brake cable would rub on the tire. #BikeNite
-
@enobacon They are adjustable, with a screw to adjust spring tension and the three holes on the post. Originally I had them all on the middle hole, but the return was not a much as I wanted so I moved them to the top hole (greatest tension), but then one of the arms apparently "failed" it still works, but a lot less tension, for that brake, I have the failed arm in the high tension hole and the working arm in the medium hole. Balances better (the screw on the failed arm does not change the tension). I don't see a way to disassemble the arm to see what is going on inside (other than destroying it).
They are Promax P-1 108mm arms. the 85mm arms I think would be just a few mm to short and the brake cable would rub on the tire. #BikeNite
@rand I haven't seen that happen but it sounds disengaged or one turn unwound in that part. Possible to loosen the adjuster screw and twist the torque pin around until it has tension? Or is the long end of the spring just slipped off the nub where it pushes against the arm?
-
And our last question this week:
Q8. What did you see this week? Share a photo if you'd like. Cycling related or not is fine. Tell us about it!
#BikeNiteQ #BikeNite #BikeTooter #Cycling #MastoBikes cc @bikenite
@ascentale @bikenite A8. I couldn't upload that much from #Spezi2026 when I was still on the move. So now I get to choose one to post in answer to the weekly photo cue.
Spezi is the best cycle show I've been to, besting even the Recumbent Cycle Con I attended 10 or so years ago. Great opportunities for disabled cyclists, but also plenty of abled cyclists enjoying the spectrum of what's available in human-powered and e-assist vehicles.
-
@ascentale @bikenite A8. My spouse finished a master’s degree this year & graduation was today, so we biked to the ceremony in style this morning. #BikeNite
@kimu @ascentale @bikenite Congratulations to them!
-
@overunderlay @ascentale @bikenite Oh, good lord! That is definitely some gritty riding. #BikeNite
-
And our last question this week:
Q8. What did you see this week? Share a photo if you'd like. Cycling related or not is fine. Tell us about it!
#BikeNiteQ #BikeNite #BikeTooter #Cycling #MastoBikes cc @bikenite
@ascentale @bikenite A8 I saw a washing machine for bikes in Antwerp! (Did not bike there this time)
-
@ascentale @bikenite A8 I saw a washing machine for bikes in Antwerp! (Did not bike there this time)
@A_denie @ascentale @bikenite Be wary of power washing bottom bracket and other sensitive parts.
-
And our last question this week:
Q8. What did you see this week? Share a photo if you'd like. Cycling related or not is fine. Tell us about it!
#BikeNiteQ #BikeNite #BikeTooter #Cycling #MastoBikes cc @bikenite
-
And our last question this week:
Q8. What did you see this week? Share a photo if you'd like. Cycling related or not is fine. Tell us about it!
#BikeNiteQ #BikeNite #BikeTooter #Cycling #MastoBikes cc @bikenite
@ascentale @bikenite A8. Today I have seen the best that can happen to an Autobahn:
Around 5000 cyclists were riding today through Frankfurt, Germany, to protest against road extension and for better alternative mobility.
To see more: #StoppA5Ausbau
#bikenite
-
@ascentale @bikenite A8. My spouse finished a master’s degree this year & graduation was today, so we biked to the ceremony in style this morning. #BikeNite
-
@ascentale @bikenite A8. My spouse finished a master’s degree this year & graduation was today, so we biked to the ceremony in style this morning. #BikeNite
@kimu @ascentale @bikenite Wow, congrats to him! How long/far did he manage to bike in the robe for?
-
@ajft @ascentale @bikenite i understand that a lentil under the valve cap is quite effective.
Repeat offenders might get one under all 4. -
And our last question this week:
Q8. What did you see this week? Share a photo if you'd like. Cycling related or not is fine. Tell us about it!
#BikeNiteQ #BikeNite #BikeTooter #Cycling #MastoBikes cc @bikenite
@ascentale @bikenite
#bikeNite #bikeNiteA
A8
At the Holmfirth Folk Festival with my partner and her Morris team.
They are the Milltown Cloggies, and the style is NorthWest Clog Morris
UK peeps may recognise Holmfirth as the setting for Last Of The Summer Wine
For everyone else, I cannot adequately explain a TV sitcom that pulls on the innate weirdness of Pennine towns.
-
R relay@relay.infosec.exchange shared this topic
